; Remember to shorten file name to 8 char for Omniterm !
;	UTILIZE INTERNAL MEMORY CHANNELS OF THE IC-706MkI FOR CTCSS/PL/CG ACCESS !
;	with the RLC-3 !
;	!
;	The purpose of this file is to be able access repeaters that require tone (CTCSS/PL/CG). !
;	ICOM did not provide commands that allows the remote programming of CTCSS/PL/CG for the IC-706 !
;	via the CI-V interface. !
;	Therefore the RLC controllers have no means to make tone access possible directly 	by using !
;	command 198 in the RLC-3 when using an ICOM IC-706 (or some other ICOM rigs). !
;	Inorder to gain this ability one must program the IC-706 internal memory channels manually !
;	or use a CI-V interface and upload software (memory manager programs are available on the web). !
;	However you still MUST ENTER the CTCSS/PL/CG TONES MANUALLY, and make sure that the ENCODE is TURNED !
;	ON for each of the IC-706's internal memory channels.(***More info at the end of this file***) !
;	!
;	This upload file was created for the IC-706MkI, but the file can be modified !
;	for use with the IC-706MkII & IC-706MkIIG (or other ICOM rigs) with slight modifications. !
;	Example:   Change the radios address (IC-706MkI) from h48 dec/072 to: !
;	IC-706MkII   h4E dec/078  or !
;	IC-706MkIIG  h58 dec/088 !
;	This can be done by changing the following in the 034 commands in the file below !
;	(example: C034x(x=port)254 254 (hFE hFE - preamble sent twice) "072"(h48 - radios addreess) !
;	to "078"(h4E/IC-706MkII) or "088"(h58/IC-706MkIIG). All of the IC-706MkI cmds are near !
;	the end of this file !
;	!
;	!
;	Be Sure To Set The IC-706's (in the menu mode) address to h48 and the baud rate to 1200 !
;	and the trans off (the IC-706 does not need to send data the the RLC-3) !
;	!
;	This file is set up as port "6" for the ICOM/HF Aux Base !
;	and the macros used are 690 - 801 !
;	---------------------------------------!
;	!
;	Enable HF Mode - Set Prefix Digit to "6" - sets up RLC-3 HF Aux Base Keypad Entry Commands !
C19516!
;	Configure HF Radio on Port 6 for ICOM IC-706MkI - sets up RLC-3 HF Aux Base Keypad Entry Commands !
;	(IC-706MkIIG=C1966178) !
C1966172!
;	BLOCK EXECUTION of ALL COMMANDS from entering port 6 (HF AUX BASE) (this is a good practice !
;	unless you are planning to control the IC-706MkIIG from its own 440 band - otherwise, it's a no no, !
;	besides you don't want junk from HF (1.8-29.7) falsing some command in your controller) !
C1306000999!
;	set the rlc-3 hf port 6 (or change 1-8) to 1200 baud (the 198 command uses 1200 baud - keep both !
;	serial message 034 and 198 at the same baud rate) !
C02461200!
;	program event 209 to execute macro 690 (split off - VFO mode - VFO-A), !
C157209690!
;	The rlc-3 will not reissue the split off cmd when command 198 is turned on. If your last use !
;	of the IC-706 was in a offset mode using the 706's internal memmory channels for CTCSS/PL/CG access !
;	(not rlc-3 memory mode) then the split needs turned off, and place to the IC-706 back in VFO-A mode !
;	program macro 690 to turn the split off before going into rlc-3 (198) hf remote mode - !
;	"split off cmd FEFE48E00F00FD" - VFO mode FEFE48E007FD - VFO A FEFE48E00700FD !
C0536900346254254072224015000253!
C0566900346254254072224007253!
C0566900346254254072224007000253!
;	!
;	MACRO 691 voice msg "hf remote base freq. set" !
C053691036587587038036408097213435!
;	START SCAN mode (on) - voice msg "scan start" !
C0536920346254254072224014001253!
C056692036660456!
;	STOP SCAN mode (off) - voice msg "scan stop" !
C0536930346254254072224014000253!
C056693036660457!
;	set MEMORY to VFO - voice msg "  "m" "o" "er" "e"  - 2 v f o" !
C0536940346254254072224010253!
C056694036043045547035002052036045!
;	set MEMORY MODE ON (should pull up last memory channel accessed) - voice msg "m o er e control" !
C0536950346254254072224008253!
C056695036043045547035142!
;	set SPLIT MODE ON - voice msg "off set pause on"!
C0536960346254254072224015001253!
C056696036354435587358!
;	set SPLIT MODE OFF - voice msg "off set pause off" !
C0536970346254254072224015000253!
C056697036354435587354!
;	set to VFO mode / VFO-A mode - voice msg "v f o pause A" !
C0566980346254254072224007000253!
C056698036052036045587031!
;	set to VFO mode / VFO-B mode - voice msg "v f o pause B" !
C0566990346254254072224007001253!
C056699036052036045587032!
;	!
;	 marcos (700-799) commands to use the IC-706's internal memory locations for CTCSS/PL/CG useage !
;	!
;	 set to memory channel 01 - voice msg: execute macro 691 ("hf remote base freq. set") - !
;	                                                voice msg "53.O1"!
C0537010346254254072224008001253!
C056701691!
C056701036023003381000001!
;	 set to memory channel 02 - execute macro 691 - voice msg "53.O3"!
C0537020346254254072224008002253!
C056702691!
C056702036023003381000003!
;	 set to memory channel 03 - execute macro 691 - voice msg "53.O5"!
C0537030346254254072224008003253!
C056703691!
C056703036023003381000005!
;	 set to memory channel 04 - execute macro 691 - voice msg "53.O7"!
C0537040346254254072224008004253!
C056704691!
C056704036023003381000007!
;	 set to memory channel 05 - execute macro 691 - voice msg "53.O9"!
C0537050346254254072224008005253!
C056705691!
C056705036023003381000009!
;	 set to memory channel 06 - execute macro 691 - voice msg "53.11"!
C0537060346254254072224008006253!
C056706691!
C056706036023003381001001!
;	 set to memory channel 07 - execute macro 691 - voice msg "53.13"!
C0537070346254254072224008007253!
C056707691!
C056707036023003381001003!
;	 set to memory channel 08 - execute macro 691 - voice msg "53.15"!
C0537080346254254072224008008253!
C056708691!
C056708036023003381001005!
;	 set to memory channel 09 - execute macro 691 - voice msg "53.17"!
C0537090346254254072224008009253!
C056709691!
C056709036023003381001007!
;	 set to memory channel 10 - execute macro 691 - voice msg "53.17" ohio!
C0537100346254254072224008016253!
C056710691!
C056710036023003381001007355!
;	 set to memory channel 11 - execute macro 691 - voice msg "53.19"!
C0537110346254254072224008017253!
C056711691!
C056711036023003381001009!
;	 set to memory channel 12 - execute macro 691 - voice msg "53.21"!
C0537120346254254072224008018253!
C056712691!
C056712036023003381002001!
;	 set to memory channel 13 - execute macro 691 - voice msg "53.23"!
C0537130346254254072224008019253!
C056713691!
C056713036023003381002003!
;	 set to memory channel 14 - execute macro 691 - voice msg "53.25"!
C0537140346254254072224008020253!
C056714691!
C056714036023003381002005!
;	 set to memory channel 15 - execute macro 691 - voice msg "53.27"!
C0537150346254254072224008021253!
C056715691!
C056715036023003381002007!
;	 set to memory channel 16 - execute macro 691 - voice msg "53.29"!
C0537160346254254072224008022253!
C056716691!
C056716036023003381002009!
;	 set to memory channel 17 - execute macro 691 - voice msg "53.31"!
C0537170346254254072224008023253!
C056717691!
C056717036023003381003001!
;	 set to memory channel 18 - execute macro 691 - voice msg "53.33"!
C0537180346254254072224008024253!
C056718691!
C056718036023003381003003!
;	 set to memory channel 19 - execute macro 691 - voice msg "53.35"!
C0537190346254254072224008025253!
C056719691!
C056719036023003381003005!
;	 set to memory channel 20 - execute macro 691 - voice msg "53.37"!
C0537200346254254072224008032253!
C056720691!
C056720036023003381003007!
;	 set to memory channel 21 - execute macro 691 - voice msg "53.39"!
C0537210346254254072224008033253!
C056721691!
C056721036023003381003009!
;	 set to memory channel 22 - execute macro 691 - voice msg "53.41"!
C0537220346254254072224008034253!
C056722691!
C056722036023003381004001!
;	 set to memory channel 23 - execute macro 691 - voice msg "53.43"!
C0537230346254254072224008035253!
C056723691!
C056723036023003381004003!
;	 set to memory channel 24 - execute macro 691 - voice msg "53.45"!
C0537240346254254072224008036253!
C056724691!
C056724036023003381004005!
;	 set to memory channel 25 - execute macro 691 - voice msg "53.47"!
C0537250346254254072224008037253!
C056725691!
C056725036023003381004007!
;	 set to memory channel 26 - execute macro 691 - voice msg "53.49"!
C0537260346254254072224008038253!
C056726691!
C056726036023003381004009!
;	 set to memory channel 27 - execute macro 691 - voice msg "53.51"!
C0537270346254254072224008039253!
C056727691!
C056727036023003381005001!
;	 set to memory channel 28 - execute macro 691 - voice msg "53.53"!
C0537280346254254072224008040253!
C056728691!
C056728036023003381005003!
;	 set to memory channel 29 - execute macro 691 - voice msg "53.55"!
C0537290346254254072224008041253!
C056729691!
C056729036023003381005005!
;	 set to memory channel 30 - execute macro 691 - voice msg "53.57"!
C0537300346254254072224008048253!
C056730691!
C056730036023003381005007!
;	 set to memory channel 31 - execute macro 691 - voice msg "53.59"!
C0537310346254254072224008049253!
C056731691!
C056731036023003381005009!
;	 set to memory channel 32 - execute macro 691 - voice msg "53.61"!
C0537320346254254072224008050253!
C056732691!
C056732036023003381006001!
;	 set to memory channel 33 - execute macro 691 - voice msg "53.63"!
C0537330346254254072224008051253!
C056733691!
C056733036023003381006003!
;	 set to memory channel 34 - execute macro 691 - voice msg "53.65"!
C0537340346254254072224008052253!
C056734691!
C056734036023003381006005!
;	 set to memory channel 35 - execute macro 691 - voice msg "53.67"!
C0537350346254254072224008053253!
C056735691!
C056735036023003381006007!
;	 set to memory channel 36 - execute macro 691 - voice msg "53.69"!
C0537360346254254072224008054253!
C056736691!
C056736036023003381006009!
;	 set to memory channel 37 - execute macro 691 - voice msg "53.71"!
C0537370346254254072224008055253!
C056737691!
C056737036023003381007001!
;	 set to memory channel 38 - execute macro 691 - voice msg "53.73"!
C0537380346254254072224008056253!
C056738691!
C056738036023003381007003!
;	 set to memory channel 39 - execute macro 691 - voice msg "53.75"!
C0537390346254254072224008057253!
C056739691!
C056739036023003381007005!
;	 set to memory channel 40 - execute macro 691 - voice msg "53.77"!
C0537400346254254072224008064253!
C056740691!
C056740036023003381007007!
;	 set to memory channel 41 - execute macro 691 - voice msg "53.79"!
C0537410346254254072224008065253!
C056741691!
C056741036023003381007009!
;	 set to memory channel 42 - execute macro 691 - voice msg "53.81"!
C0537420346254254072224008066253!
C056742691!
C056742036023003381008001!
;	 set to memory channel 43 - execute macro 691 - voice msg "53.83"!
C0537430346254254072224008067253!
C056743691!
C056743036023003381008003!
;	 set to memory channel 44 - execute macro 691 - voice msg "53.85"!
C0537440346254254072224008068253!
C056744691!
C056744036023003381008005!
;	 set to memory channel 45 - execute macro 691 - voice msg "53.87"!
C0537450346254254072224008069253!
C056745691!
C056745036023003381008007!
;	 set to memory channel 46 - execute macro 691 - voice msg "53.89"!
C0537460346254254072224008070253!
C056746691!
C056746036023003381008009!
;	 set to memory channel 47 - execute macro 691 - voice msg "53.91"!
C0537470346254254072224008071253!
C056747691!
C056747036023003381009001!
;	 set to memory channel 48 - execute macro 691 - voice msg "53.93"!
C0537480346254254072224008072253!
C056748691!
C056748036023003381009003!
;	 set to memory channel 49 - execute macro 691 - voice msg "53.95"!
C0537490346254254072224008073253!
C056749691!
C056749036023003381009005!
;	 set to memory channel 50 - execute macro 691 - voice msg "53.97"!
C0537500346254254072224008080253!
C056750691!
C056750036023003381009007!
;	 set to memory channel 51 - execute macro 691 - voice msg "53.99"!
C0537510346254254072224008081253!
C056751691!
C056751036023003381009009!
;	 set to memory channel 52 - execute macro 691 - voice msg "145.11"!
C0537520346254254072224008082253!
C056752691!
C056752036001022005381001001!
;	 set to memory channel 53 - execute macro 691 - voice msg "145.17"!
C0537530346254254072224008083253!
C056753691!
C056753036001022005381001007!
;	 set to memory channel 54 - execute macro 691 - voice msg "145.19"!
C0537540346254254072224008084253!
C056754691!
C056754036001022005381001009!
;	 set to memory channel 55 - execute macro 691 - voice msg "145.19 ohio"!
C0537550346254254072224008085253!
C056755691!
C056755036001022005381001009355!
;	 set to memory channel 56 - execute macro 691 - voice msg "145.21"!
C0537560346254254072224008086253!
C056756691!
C056756036001022005381002001!
;	 set to memory channel 57 - execute macro 691 - voice msg "145.23"!
C0537570346254254072224008087253!
C056757691!
C056757036001022005381002003!
;	 set to memory channel 58 - execute macro 691 - voice msg "145.27"!
C0537580346254254072224008088253!
C056758691!
C056758036001022005381002007!
;	 set to memory channel 59 - execute macro 691 - voice msg "145.31"!
C0537590346254254072224008089253!
C056759691!
C056759036001022005381003001!
;	 set to memory channel 60 - execute macro 691 - voice msg "145.33"!
C0537600346254254072224008096253!
C056760691!
C056760036001022005381003003!
;	 set to memory channel 61 - execute macro 691 - voice msg "145.35"!
C0537610346254254072224008097253!
C056761691!
C056761036001022005381003005!
;	 set to memory channel 62 - execute macro 691 - voice msg "145.41"!
C0537620346254254072224008098253!
C056762691!
C056762036001022005381004001!
;	 set to memory channel 63 - execute macro 691 - voice msg "145.43" MGW!
C0537630346254254072224008099253!
C056763691!
C056763036001022005381004003!
;	 set to memory channel 64 - execute macro 691 - voice msg "145.45"!
C0537640346254254072224008100253!
C056764691!
C056764036001022005381004005!
;	 set to memory channel 65 - execute macro 691 - voice msg "145.47"!
C0537650346254254072224008101253!
C056765691!
C056765036001022005381004007!
;	 set to memory channel 66 - execute macro 691 - voice msg "146.625"!
C0537660346254254072224008102253!
C056766691!
C056766036001022006381006002005!
;	 set to memory channel 67 - execute macro 691 - voice msg "146.655"!
C0537670346254254072224008103253!
C056767691!
C056767036001022006381006005005!
;	 set to memory channel 68 - execute macro 691 - voice msg "146.67"!
C0537680346254254072224008104253!
C056768691!
C056768036001022006381006007!
;	 set to memory channel 69 - execute macro 691 - voice msg "146.685"!
C0537690346254254072224008105253!
C056769691!
C056769036001022006381006008005!
;	 set to memory channel 70 - execute macro 691 - voice msg "146.700"!
C0537700346254254072224008112253!
C056770691!
C056770036001022006381007000000!
;	 set to memory channel 71 - execute macro 691 - voice msg "146.73"!
C0537710346254254072224008113253!
C056771691!
C056771036001022006381007003!
;	 set to memory channel 72 - execute macro 691 - voice msg "146.76"!
C0537720346254254072224008114253!
C056772691!
C056772036001022006381007006!
;	 set to memory channel 73 - execute macro 691 - voice msg "146.85"!
C0537730346254254072224008115253!
C056773691!
C056773036001022006381008005!
;	 set to memory channel 74 - execute macro 691 - voice msg "146.88"!
C0537740346254254072224008116253!
C056774691!
C056774036001022006381008008!
;	 set to memory channel 75 - execute macro 691 - voice msg "146.895"!
C0537750346254254072224008117253!
C056775691!
C056775036001022006381008009005!
;	 set to memory channel 76 - execute macro 691 - voice msg "146.94"!
C0537760346254254072224008118253!
C056776691!
C056776036001022006381006009004!
;	 set to memory channel 77 - execute macro 691 - voice msg "147.06"!
C0537770346254254072224008119253!
C056777691!
C056777036001022007381000006!
;	 set to memory channel 78 - execute macro 691 - voice msg "147.075!
C0537780346254254072224008120253!
C056778691!
C056778036001022007381000007005!
;	 set to memory channel 79 - execute macro 691 - voice msg "147.105"!
C0537790346254254072224008121253!
C056779691!
C056779036001022007381001000005!
;	 set to memory channel 80 - execute macro 691 - voice msg "147.12"!
C0537800346254254072224008128253!
C056780691!
C056780036001022007381001002!
;	 set to memory channel 81 - execute macro 691 - voice msg "147.135"!
C0537810346254254072224008129253!
C056781691!
C056781036001022007381001003005!
;	 set to memory channel 82 - execute macro 691 - voice msg "147.15"!
C0537820346254254072224008130253!
C056782691!
C056782036001022007381001005!
;	 set to memory channel 83 - execute macro 691 - voice msg "147.195"!
C0537830346254254072224008131253!
C056783691!
C056783036001022007381001009005!
;	 set to memory channel 84 - execute macro 691 - voice msg "147.21"!
C0537840346254254072224008132253!
C056784691!
C056784036001022007381002001!
;	 set to memory channel 85 - execute macro 691 - voice msg "147.225"!
C0537850346254254072224008133253!
C056785691!
C056785036001022007381002002005!
;	 set to memory channel 86 - execute macro 691 - voice msg "147.24"!
C0537860346254254072224008134253!
C056786691!
C056786036001022007381002004!
;	 set to memory channel 87 - execute macro 691 - voice msg "147.24 KY"!
C0537870346254254072224008135253!
C056787691!
C056787036001022007381002004276!
;	 set to memory channel 88 - execute macro 691 - voice msg "147.255"!
C0537880346254254072224008136253!
C056788691!
C056788036001022007381002005005!
;	 set to memory channel 89 - execute macro 691 - voice msg "147.27"!
C0537890346254254072224008137253!
C056789691!
C056789036001022007381002007!
;	 set to memory channel 90 - execute macro 691 - voice msg "147.36"!
C0537900346254254072224008144253!
C056790691!
C056790036001022007381003006!
;	 set to memory channel 91 - execute macro 691 - voice msg "147.36 ohio"!
C0537910346254254072224008145253!
C056791691!
C056791036001022007381003006355!
;	 set to memory channel 92 - execute macro 691 - voice msg "147.375"!
C0537920346254254072224008146253!
C056792691!
C056792036001022007381003007005!
;	 set to memory channel 93 - execute macro 691 - voice msg "147.36 ohio"!
C0537930346254254072224008147253!
C056793691!
C056793036001022007381003006355!
;	 set to memory channel 94 - execute macro 691 - voice msg "147.39"!
C0537940346254254072224008148253!
C056794691!
C056794036001022007381003009!
;	 set to memory channel 95 - execute macro 691 - voice msg "29.62"!
C0537950346254254072224008149253!
C056795691!
C056795036020009381006002!
;	 set to memory channel 96 - execute macro 691 - voice msg "29.64"!
C0537960346254254072224008150253!
C056796691!
C056796036020009381006004!
;	 set to memory channel 97 - execute macro 691 - voice msg "29.64 red"!
C0537970346254254072224008151253!
C056797691!
C056797036020009381006004405!
;	 set to memory channel 98 - execute macro 691 - voice msg "29.66"!
C0537980346254254072224008152253!
C056798691!
C056798036020009381006006!
;	 set to memory channel 99 - execute macro 691 - voice msg "29.68"!
C0537990346254254072224008153253!
C056799691!
C056799036020009381006008!
;	 set to memory mode - set to memory channel P1 !
;xC0568000346254254072224008001000253!
;	 set to memory mode - set to memory channel P2 !
;xC0568010346254254072224008001001253!
;	!
;	!
;	 change cmd 701 to 53*01 - level 1 !
C01070153*01!
C1907011!
;	 change cmd 702 to 53*03 - level 1 !
C01070253*03!
C1907021!
;	 change cmd 703 to 53*05 - level 1 !
C01070353*05!
C1907031!
;	 change cmd 704 to 53*07 - level 1 !
C01070453*07!
C1907041!
;	 change cmd 705 to 53*09 - level 1 !
C01070553*09!
C1907051!
;	 change cmd 706 to 53*11 - level 1 !
C01070653*11!
C1907061!
;	 change cmd 707 to 53*13 - level 1 !
C01070753*13!
C1907071!
;	 change cmd 708 to 53*15 - level 1 !
C01070853*15!
C1907081!
;	 change cmd 709 to 53*17 - level 1 !
C01070953*17!
C1907091!
;	 change cmd 710 to 53*172 - level 1 !
C01071053*172!
C1907101!
;	 change cmd 711 to 53*19 - level 1 !
C01071153*19!
C1907111!
;	 change cmd 712 to 53*21 - level 1 !
C01071253*21!
C1907121!
;	 change cmd 713 to 53*23 - level 1 !
C01071353*23!
C1907131!
;	 change cmd 714 to 53*25 - level 1 !
C01071453*25!
C1907141!
;	 change cmd 715 to 53*27 - level 1 !
C01071553*27!
C1907151!
;	 change cmd 716 to 53*29 - level 1 !
C01071653*29!
C1907161!
;	 change cmd 717 to 53*31 - level 1 !
C01071753*31!
C1907171!
;	 change cmd 718 to 53*33 - level 1 !
C01071853*33!
C1907181!
;	 change cmd 719 to 53*35 - level 1 !
C01071953*35!
C1907191!
;	 change cmd 720 to 53*37 - level 1 !
C01072053*37!
C1907201!
;	 change cmd 721 to 53*39 - level 1 !
C01072153*39!
C1907211!
;	 change cmd 722 to 53*41 - level 1 !
C01072253*41!
C1907221!
;	 change cmd 723 to 53*43 - level 1 !
C01072353*43!
C1907231!
;	 change cmd 724 to 53*45 - level 1 !
C01072453*45!
C1907241!
;	 change cmd 725 to 53*47 - level 1 !
C01072553*47!
C1907251!
;	 change cmd 726 to 53*49 - level 1 !
C01072653*49!
C1907261!
;	 change cmd 727 to 53*51 - level 1 !
C01072753*51!
C1907271!
;	 change cmd 728 to 53*53 - level 1 !
C01072853*53!
C1907281!
;	 change cmd 729 to 53*55 - level 1 !
C01072953*55!
C1907291!
;	 change cmd 730 to 53*57 - level 1 !
C01073053*57!
C1907301!
;	 change cmd 731 to 53*59 - level 1 !
C01073153*59!
C1907311!
;	 change cmd 732 to 53*61 - level 1 !
C01073253*61!
C1907321!
;	 change cmd 733 to 53*63 - level 1 !
C01073353*63!
C1907331!
;	 change cmd 734 to 53*65 - level 1 !
C01073453*65!
C1907341!
;	 change cmd 735 to 53*67 - level 1 !
C01073553*67!
C1907351!
;	 change cmd 736 to 53*69 - level 1 !
C01073653*69!
C1907361!
;	 change cmd 737 to 53*71 - level 1 !
C01073753*71!
C1907371!
;	 change cmd 738 to 53*73 - level 1 !
C01073853*73!
C1907381!
;	 change cmd 739 to 53*75 - level 1 !
C01073953*75!
C1907391!
;	 change cmd 740 to 53*77 - level 1 !
C01074053*77!
C1907401!
;	 change cmd 741 to 53*79 - level 1 !
C01074153*79!
C1907411!
;	 change cmd 742 to 53*81 - level 1 !
C01074253*81!
C1907421!
;	 change cmd 743 to 53*83 - level 1 !
C01074353*83!
C1907431!
;	 change cmd 744 to 53*85 - level 1 !
C01074453*85!
C1907441!
;	 change cmd 745 to 53*87 - level 1 !
C01074553*87!
C1907451!
;	 change cmd 746 to 53*89 - level 1 !
C01074653*89!
C190746!
;	 change cmd 747 to 53*91 - level 1 !
C01074753*91!
C1907471!
;	 change cmd 748 to 53*93 - level 1 !
C01074853*93!
C1907481!
;	 change cmd 749 to 53*95 - level 1 !
C01074953*95!
C1907491!
;	 change cmd 750 to 53*97 - level 1 !
C01075053*97!
C1907501!
;	 change cmd 751 to 53*99 - level 1 !
C01075153*99!
C1907511!
;	  !
;	 ************************     PLEASE NOTE      *************************** !
;	 When renaming some of the 2 meter (or 440) frequencies - the RLC-3 010    !
;	 command will NOT allow more than 6 digits, therefore this file has errors !
;	 on every VHF(UHF) frequency that uses more than 6 digits                  !
;	 EXAMPLE:   " 146*625 ,  146*655   ,   146*685   ,  etc. "                 !
;	 ************************     PLEASE NOTE      *************************** !
;	  !
;	 change cmd 752 to 145*11 - level 1 !
C010752145*11!
C1907521!
;	 change cmd 753 to 145*17 - level 1 !
C010753145*17!
C1907531!
;	 change cmd 754 to 145*19 - level 1 !
C010754145*19!
C1907541!
;	 change cmd 755 to 145*192 - level 1 !
C010755145*192!
C1907551!
;	 change cmd 756 to 145*21 - level 1 !
C010756145*21!
C1907561!
;	 change cmd 757 to 145*23 - level 1 !
C010757145*23!
C1907571!
;	 change cmd 758 to 145*27 - level 1 !
C010758145*27!
C1907581!
;	 change cmd 759 to 145*31 - level 1 !
C010759145*31!
C1907591!
;	 change cmd 760 to 145*33 - level 1 !
C010760145*33!
C1907601!
;	 change cmd 761 to 145*35 - level 1 !
C010761145*35!
C1907611!
;	 change cmd 762 to 145*41 - level 1 !
C010762145*41!
C1907621!
;	 change cmd 763 to 145*43 - level 1 !
C010763145*43!
C1907631!
;	 change cmd 764 to 145*45 - level 1 !
C010764145*45!
C1907641!
;	 change cmd 765 to 145*47 - level 1 !
C010765145*47!
C1907651!
;	 change cmd 766 to 146*625 - level 1 !
C010766146*625!
C1907661!
;	 change cmd 767 to 146*655 - level 1 !
C010767146*655!
C1907671!
;	 change cmd 768 to 146*67 - level 1 !
C010768146*67!
C1907681!
;	 change cmd 769 to 146*685 - level 1 !
C010769146*685!
C1907691!
;	 change cmd 770 to 146*7 - level 1 !
C010770146*7!
C1907701!
;	 change cmd 771 to 146*73 - level 1 !
C010771146*73!
C1907711!
;	 change cmd 772 to 146*76 - level 1 !
C010772146*76!
C1907721!
;	 change cmd 773 to 146*85- level 1 !
C010773146*85!
C1907731!
;	 change cmd 774 to 146*88 - level 1 !
C010774146*88!
C1907741!
;	 change cmd 775 to 146*895 - level 1 !
C010775146*895!
C1907751!
;	 change cmd 776 to 146*94 - level 1 !
C010776146*94!
C1907761!
;	 change cmd 777 to 147*06 - level 1 !
C010777147*06!
C1907771!
;	 change cmd 778 to 147*075 - level 1 !
C010778147*075!
C1907781!
;	 change cmd 779 to 147*105 - level 1 !
C010779147*105!
C1907791!
;	 change cmd 780 to 147*12 - level 1 !
C010780147*12!
C1907801!
;	 change cmd 781 to 147*135 - level 1 !
C010781147*135!
C1907811!
;	 change cmd 782 to 147*15 - level 1 !
C010782147*15!
C1907821!
;	 change cmd 783 to 147*195 - level 1 !
C010783147*195!
C1907831!
;	 change cmd 784 to 147*21 - level 1 !
C010784147*21!
C1907841!
;	 change cmd 785 to 147*225 - level 1 !
C010785147*225!
C1907851!
;	 change cmd 786 to 147*24 - level 1 !
C010786147*24!
C1907861!
;	 change cmd 787 to 147*242 - level 1 !
C010787147*242!
C1907871!
;	 change cmd 788 to 147*255 - level 1 !
C010788147*255!
C1907881!
;	 change cmd 789 to 147*27 - level 1 !
C010789147*27!
C1907891!
;	 change cmd 790 to 147*36 - level 1 !
C010790147*36!
C1907901!
;	 change cmd 791 to 147*362 - level 1 !
C010791147*362!
C1907911!
;	 change cmd 792 to 147*375 - level 1 !
C010792147*375!
C1907921!
;	 change cmd 793 to 147*39 - level 1 !
C010793147*39!
C1907931!
;	 change cmd 794 to 147*392 - level 1 !
C010794147*392!
C1907941!
;	 change cmd 795 to 29*62 - level 1 !
C01079529*62!
C1907951!
;	 change cmd 796 to 29*64 - level 1 !
C01079629*64!
C1907961!
;	 change cmd 797 to 29*642 - level 1 !
C01079729*642!
C1907971!
;	 change cmd 798 to 29*66 - level 1 !
C01079829*66!
C1907981!
;	 change cmd 799 to 29*68 - level 1 !
C01079929*68!
C1907991!
;!
;!
;	 MORE VHF REMOTE FREQS (with out PL) This section sets frequencies to the !
;	 IC-706 via the RLC-3 command 199 and allows 000,001,002 cmds to be used  !
;!
;!
;	 execute macro 691 - set freq 145.13 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 920 to 145*13 - level 1 !
C053920691!
C0569201996145*13!
C056920038!
C056920199614!
C05692019968113!
C010920145*13!
C1909201!
;	 execute macro 691 - set freq 145.15 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 921 to 145*15 - level 1 !
C053921691!
C0569211996145*15!
C056921038!
C056921199614!
C05692119968113!
C010921145*15!
C1909211!
;	 execute macro 691 - set freq 145.25 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 922 to 145*25 - level 1 !
C053922691!
C0569221996145*25!
C056922038!
C056922199614!
C05692219968113!
C010922145*25!
C1909221!
;	 execute macro 691 - set freq 145.29 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 923 to 145*29 - level 1 !
C053923691!
C0569231996145*29!
C056923038!
C056923199614!
C05692319968113!
C010923145*29!
C1909231!
;	 execute macro 691 - set freq 145.49 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 924 to 145*49 - level 1 !
C053924691!
C0569241996145*49!
C056924038!
C056924199614!
C05692419968113!
C010924145*49!
C1909241!
;	 execute macro 691 - set freq 52.47 - audio off - set mode fm - set offset off & !
;	 no split - change cmd 925 to 52*47 - level 1 !
C053925691!
C056925199652*47!
C056925038!
C056925199614!
C056925199680!
C01092552*47!
C1909251!
;	 execute macro 691 - set freq 52.49 - audio off - set mode fm - set offset off & !
;	 no split - change cmd 926 to 52*49 - level 1 !
C053926691!
C056926199652*49!
C056926038!
C056926199614!
C056926199680!
C01092652*49!
C1909261!
;	 execute macro 691 - set freq 52.525 - audio off - set mode fm - set offset off & !
;	 no split - change cmd 927 to 52*525 - level 1 !
C053927691!
C056927199652*525!
C056927038!
C056927199614!
C056927199680!
C01092752*52!
C1909271!
;	 execute macro 691 - set freq 52.55 - audio off - set mode fm - set offset off & !
;	 no split - change cmd 928 to 52*55 - level 1 !
C053928691!
C056928199652*55!
C056928038!
C056928199614!
C056928199680!
C01092852*55!
C1909281!
;	 execute macro 691 - set freq 52.57 - audio off - set mode fm - set offset off & !
;	 no split - change cmd 929 to 52*57 - level 1 !
C053929691!
C056929199652*57!
C056929038!
C056929199614!
C056929199680!
C01092952*57!
C1909291!
;	 execute macro 691 - set freq 146.475 - audio off - set mode fm - set offset off & !
;	 no split - change cmd 930 to 146*475 - level 1 !
C053930691!
C0569301996146*475!
C056930038!
C056930199614!
C056930199680!
C010930146*475!
C1909301!
;	 execute macro 691 - set freq 146.49 - audio off - set mode fm - set offset off & !
;	 no split - change cmd 931 to 146*49 - level 1 !
C053931691!
C0569311996146*49!
C056931038!
C056931199614!
C056931199680!
C010931146*49!
C1909311!
;	 execute macro 691 - set freq 146.535 - audio off - set mode fm - set offset off & !
;	 no split to - change cmd 932 to 146*535 - level 1 !
C053932691!
C0569321996146*535!
C056932038!
C056932199614!
C056932199680!
C010932146*535!
C1909321!
;	 execute macro 691 - set freq 146.55 - audio off - set mode fm - set offset off & !
;	 no split - change cmd 933 to 146*55 - level 1 !
C053933691!
C0569331996146*55!
C056933038!
C056933199614!
C056933199680!
C010933146*55!
C1909331!
;	 execute macro 691 - set freq 146.565 - audio off - set mode fm - set offset off & !
;	 no split to - change cmd 934 to 146*565 - level 1 !
C053934691!
C0569341996146*565!
C056934038!
C056934199614!
C056934199680!
C010934146*565!
C1909341!
;	 execute macro 691 - set freq 146.58 - audio off - set mode fm - set offset off & !
;	 no split - change cmd 935 to 146*58 - level 1 !
C053935691!
C0569351996146*58!
C056935038!
C056935199614!
C056935199680!
C010935146*58!
C1909351!
;	 execute macro 691 - set freq 146.61 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 936 to 146*61 - level 1 !
C053936691!
C0569361996146*61!
C056936038!
C056936199614!
C05693619968113!
C010936146*61!
C1909361!
;	 execute macro 691 - set freq 146.64 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 937 to 146*64 - level 1 !
C053937691!
C0569371996146*64!
C056937038!
C056937199614!
C05693719968113!
C010937146*64!
C1909371!
;	 execute macro 691 - set freq 146.715 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 938 to 146*715 - level 1 !
C053938691!
C0569381996146*715!
C056938038!
C056938199614!
C05693819968113!
C010938146*715!
C1909381!
;	 execute macro 691 - set freq 146.745 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 939 to 146*745 - level 1 !
C053939691!
C0569391996146*745!
C056939038!
C056939199614!
C05693919968113!
C010939146*745!
C1909391!
;	 execute macro 691 - set freq 146.775 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 940 to 146*775 - level 1 !
C053940691!
C0569401996146*775!
C056940038!
C056940199614!
C05694019968113!
C010940146*775!
C1909401!
;	 execute macro 691 - set freq 146.79 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 941 to 146*79 - level 1 !
C053941691!
C0569411996146*79!
C056941038!
C056941199614!
C05694119968113!
C010941146*79!
C1909411!
;	 execute macro 691 - set freq 146.805 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 942 to 146*805 - level 1 !
C053942691!
C0569421996146*805!
C056942038!
C056942199614!
C05694219968113!
C010942146*805!
C1909421!
;	 execute macro 691 - set freq 146.82 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 943 to 146*82 - level 1 (MAY NEED TONE 192.8) !
C053943691!
C0569431996146*82!
C056943038!
C056943199614!
C05694319968113!
C010943146*82!
C1909431!
;	 execute macro 691 - set freq 146.835- audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 944 to 146*835 - level 1 !
C053944691!
C0569441996146*835!
C056944038!
C056944199614!
C05694419968113!
C010944146*835!
C1909441!
;	 execute macro 691 - set freq 146.865 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 945 to 146*865 - level 1 !
C053945691!
C0569451996146*865!
C056945038!
C056945199614!
C05694519968113!
C010945146*865!
C1909451!
;	 execute macro 691 - set freq 146.91 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 946 to 146*91 - level 1 !
C053946691!
C0569461996146*91!
C056946038!
C056946199614!
C05694619968113!
C010946146*91!
C1909461!
;	 execute macro 691 - set freq 146.925 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 947 to 146*925 - level 1 !
C053947691!
C0569471996146*925!
C056947038!
C056947199614!
C05694719968113!
C010947146*925!
C1909471!
;	 execute macro 691 - set freq 146.955 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 948 to 146*955 - level 1 !
C053948691!
C0569481996146*955!
C056948038!
C056948199614!
C05694819968113!
C010948146*955!
C1909481!
;	 execute macro 691 - set freq 146.97 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 949 to 146*97 - level 1 !
C053949691!
C0569491996146*97!
C056949038!
C056949199614!
C05694919968113!
C010949146*97!
C1909491!
;	 execute macro 691 - set freq 146.985 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 950 to 146*985 - level 1 !
C053950691!
C0569501996146*985!
C056950038!
C056950199614!
C05695019968113!
C010950146*985!
C1909501!
;	 execute macro 691 - set freq 147.00 - audio off - set mode fm - set offset on & !
;	 split to -0.6 - change cmd 951 to 147*00 - level 1 !
C053951691!
C0569511996147*!
C056951038!
C056951199614!
C05695119968113!
C010951147*000!
C1909511!
;	 execute macro 691 - set freq 147.00 - audio off - set mode fm - set offset on & !
;	 split to +0.6 - change cmd 952 to 147*00 - level 1 !
C053952691!
C0569521996147*!
C056952038!
C056952199614!
C05695219968103!
C010952147*0002!
C1909521!
;	 execute macro 691 - set freq 147.015 - audio off - set mode fm - set offset on & !
;	 split to +0.6 - change cmd 953 to 147*015 - level 1 !
C053953691!
C0569531996147*015!
C056953038!
C056953199614!
C05695319968103!
C010953147*015!
C1909531!
;	 execute macro 691 - set freq 147.03 - audio off - set mode fm - set offset on & !
;	 split to +0.6 - change cmd 954 to 147*03 - level 1 !
C053954691!
C0569541996147*03!
C056954038!
C056954199614!
C05695419968103!
C010954147*03!
C1909541!
;	 execute macro 691 - set freq 147.045 - audio off - set mode fm - set offset on & !
;	 split to +0.6 - change cmd 955 to 147*045 - level 1 !
C053955691!
C0569551996147*045!
C056955038!
C056955199614!
C05695519968103!
C010955147*045!
C1909551!
;	 execute macro 691 - set freq 147.090 - audio off - set mode fm - set offset on & !
;	 split to +0.6 - change cmd 956 to 147*090 - level 1 !
C053956691!
C0569561996147*09!
C056956038!
C056956199614!
C05695619968103!
C010956147*09!
C1909561!
;	 execute macro 691 - set freq 147.165 - audio off - set mode fm - set offset on & !
;	 split to +0.6 - change cmd 957 to 147*165 - level 1 !
C053957691!
C0569571996147*165!
C056957038!
C056957199614!
C05695719968103!
C010957147*165!
C1909571!
;	 execute macro 691 - set freq 147.18 - audio off - set mode fm - set offset on & !
;	 split to +0.6 - change cmd 958 to 147*18 - level 1 !
C053958691!
C0569581996147*18!
C056958038!
C056958199614!
C05695819968103!
C010958147*18!
C1909581!
;	 execute macro 691 - set freq 147.285 - audio off - set mode fm - set offset on & !
;	 split to +0.6 - change cmd 959 to 147*285 - level 1 !
C053959691!
C0569591996147*285!
C056959038!
C056959199614!
C05695919968103!
C010959147*285!
C1909591!
;	 execute macro 691 - set freq 147.30 - audio off - set mode fm - set offset on & !
;	 split to +0.6 - change cmd 960 to 147*30 - level 1 !
C053960691!
C0569601996147*3!
C056960038!
C056960199614!
C05696019968103!
C010960147*3!
C1909601!
;	 execute macro 691 - set freq 147.315 - audio off - set mode fm - set offset on & !
;	 split to +0.6 - change cmd 961 to 147*315 - level 1 !
C053961691!
C0569611996147*315!
C056961038!
C056961199614!
C05696119968103!
C010961147*315!
C1909611!
;	 execute macro 691 - set freq 147.33 - audio off - set mode fm - set offset on & !
;	 split to +0.6 - change cmd 962 to 147*33 - level 1 !
C053962691!
C0569621996147*33!
C056962038!
C056962199614!
C05696219968103!
C010962147*33!
C1909621!
;	 execute macro 691 - set freq 147.345 - audio off - set mode fm - set offset on & !
;	 split to +0.6 - change cmd 963 to 147*345 - level 1 !
C053963691!
C0569631996147*345!
C056963038!
C056963199614!
C05696319968103!
C010963147*345!
C1909631!
;	!
;	!
;	!
;	!
;	*************************************************************************         !
;	!
;       IC-706 Command Table !
!
;Description		Cn(Command Number)		Sc(Sub Command) !
;			HEX / DEC !
;Preamble Code	FE / (254) !
;End Of Msg (eot)	FD / (253) !
;IC-706MkI		48 / (072) !
;      MkII		4E / (078) !
;      MkIIG		58 / (088) !
;Terminal Sending	E0 / (224) !
:Frequency Control	05 / (005)			Data 				(see example below) !
;Mode			06 / (006)			00 / (000)	LSB !
;							01 / (001)	USB !
;							02 / (002)	AM  !
;							03 / (003)	CW  	,	02 / (002) to select filter(s) !
;							04 / (004)	RTTY!
;							05 / (005)	FM  !
;							06 / (006)	WFM !
;VFO			07 / (007)			-		VFO-Mode !
;							00 / (000)	VFO-A !
;							01 / (001)	VFO-B !
;							A0 / (160)	A=B !
;							B0 / (176)	A/B !
;Memory Mode		08 / (008)			- !
;   "	   "		08 / (008)			XX / (xxx)mc=memory channels 01-99 !
;								P1=0100 / (001&000) 	,	P2=0101 / (001&001) !
;								See HEX/DEC Table Below !
;Memory Write	09 / (009)			- !
;Memory to VFO	0A / (010)			- !
;Memory Clear	0B / (011)			- !
;Scan			0E / (014)			00 / (000)	Stop  !
;							01 / (001)	Start !
;Split			0F				00 / (000)	Off !
;							01 / (001)	On  !
;Tuning Speed	10				00 / (000)	10  Hz  !
;							01 / (001)	100 HZ  !
;							02 / (002)	1 KHz   !
;							03 / (003)	5 KHz   !
;							04 / (004)	9 KHz   !
;							05 / (005)	10 KHz  !
;							06 / (006)	12.5 KHz!
;							07 / (007)	20 KHz  !
;							08 / (008)	25 KHz  !
;							09 / (009)	100 KHz !
!
;Controller / Terminal to IC-706 Command Structure !
;	FE FE 48(to-adr) E0(fm-adr) Cn(command) Sc(sub-command) DATA FD(end of msg) !
Example:	FE FE 48 E0 Cn Sc Data FD   OR   Example:  to Enter Freq 145.282 376 MHz!
; 		P  P  I  T  C  S  F    E         FE FE 48 E0 05 (Freq) 76 23 28 45 01 FD !
;		r  r  C  e  m  u  r    n         Freq Data is Xfered LEAST Significant Byte First(1 Hz to 1 GHz)!
;		e  e  -  r  d  b  e    d         Example DEC: 254 254 072 224 (Freq= 118 035 040 069 001) 253 !
;		a  a  7  m        q              76 is 10 Hz & 1 Hz !
;		m  m  0  i  #  C  /    M         23 is 1 KHz & 100 Hz !
;		b  b  6  n     m  e    s         28 is 100 KHz & 10 KHz !
;		l  l  M  a     d  t    g         45 is 10 MHz & 1 MHz !
;		e  e  1  l     #  c              01 is 1 GHz & 100 MHz !
!
;IC-706 to Controller / Terminal Command Structure !
;Example:	FE FE E0 48 Cn Sc Data FD !
;		GOOD Response Msg:	FE FE E0 48 FB FD !
;		BAD  Response Msg:	FE FE E0 48 FA FD !
!
!
;	Hexidecimal / Decimal 	Tables:  !
;	h00-h09 / (000-009)	, 	h0A-h0F / (010-015)	,	h10-h19 / (016-025)	,	h1A-h1F / (026-031) !
;	h20-h29 / (032-041)	, 	h2A-h2F / (042-047)	,	h30-h39 / (048-057)	,	h3A-h3F / (058-063) !
;	h40-h49 / (064-073)	, 	h4A-h4F / (074-079)	,	h50-h59 / (080-089)	,	h5A-h5F / (090-095) !
;	h60-h69 / (096-105)	, 	h6A-h6F / (106-111)	,	h70-h79 / (112-121)	,	h7A-h7F / (122-127) !
;	h80-h89 / (128-137)	, 	h8A-h8F / (138-143)	,	h90-h99 / (144-153)	,	h9A-h9F / (154-159) !
;	hA0-hA9 / (160-169)	, 	hAA-hAF / (170-175)	,	hB0-hB9 / (176-185)	,	hBA-hBF / (186-191) !
;	hC0-hC9 / (192-201)	,	hCA-hCF / (202-207)	,	hD0-hD9 / (208-217)	,	hDA-hDF / (218-223) !
;	hE0-hE9 / (224-233)	,	hEA-hEF / (234-239)	,	hF0-hF9 / (240-249)	,	hFA-hFF / (250-255) !
!
!
!
;	set FREQUENCY (see example in the hex description above to see how to enter DEC values)!
C053xxx0346254254072224005xxxxxxxxxx253!
;	set MODE	LSB !
C053xxx0346254254072224006000253!
;	set MODE	USB !
C053xxx0346254254072224006001253!
;	set MODE	AM  !
C053xxx0346254254072224006002253!
;	set MODE	CW  !
C053xxx0346254254072224006003253!
;	set MODE	RTTY !
C053xxx0346254254072224006004253!
;	set MODE	FM   !
C053xxx0346254254072224006005253!
;	set MODE	WFM  !
C053xxx0346254254072224006006253!
;	set to VFO mode / VFO-A mode !
C056xxx0346254254072224007000253!
;	set to VFO mode / VFO-B mode !
C056xxx0346254254072224007001253!
;	set to VFO mode / VFO A=B mode !
C056xxx0346254254072224007160253!
;	set to VFO mode / VFO A/B mode !
C056xxx0346254254072224007176253!
;	set MEMORY MODE ON !
C053xxx0346254254072224008253!
;	set MEMORY CHANNEL - goto memory channel 01-99 / enter DEC values only for yyy!
C053xxx0346254254072224008yyy253!
;	set MEMORY MODE WRITE !
C053xxx0346254254072224009253!
;	set MEMORY to VFO !
C053xxx0346254254072224010253!
;	set MEMORY CLEAR - to erase a memory channel !
C053xxx0346254254072224011253!
;	START SCAN mode (on) !
C053xxx0346254254072224014001253!
;	STOP SCAN mode (off) !
C053xxx0346254254072224014000253!
;	set SPLIT MODE ON (offset on) !
C053xxx0346254254072224015001253!
;	set SPLIT MODE OFF (offset off) !
C053xxx0346254254072224015000253!
;	set TUNNING SPEED to 10 Hz !
C053xxx0346254254072224016000253!
;	set TUNNING SPEED to 100 Hz !
C053xxx0346254254072224016001253!
;	set TUNNING SPEED to 1 KHz !
C053xxx0346254254072224016002253!
;	set TUNNING SPEED to 5 KHz !
C053xxx0346254254072224016003253!
;	set TUNNING SPEED to 9 KHz !
C053xxx0346254254072224016004253!
;	set TUNNING SPEED to 10 KHz !
C053xxx0346254254072224016005253!
;	set TUNNING SPEED to 12.5 KHz !
C053xxx0346254254072224016006253!
;	set TUNNING SPEED to 20 KHz !
C053xxx0346254254072224016007253!
;	set TUNNING SPEED to 25 KHz !
C053xxx0346254254072224016008253!
;	set TUNNING SPEED to 100 KHz !
C053xxx0346254254072224016009253!
;!
;!
;!
;!
;!
;	Other Information: !
:!
;	One thing that ICOM has done is that they have not changed many of the HEX commands !
;	between various rigs, so this file should work on other ICOM radios that have internal !
;	memory channels (they have added newer commands to some of the more current gear - !
;	such as control over NB AGC VOX etc. so some research may be required as assure !
;	no conflicts between this file and other ICOM radios. !
;!
;	One other thing that may be of use for CTCSS/PL/CG access regarding the IC-706 and !
;	RLC-3, however it is a bit more trouble to use. The IC-706 will remember the last !
;	CTCSS/PL/CG tone the radio used. For example the radio could be programmed with all !
;	the CTCSS/PL/CG tones on one freq. (example 146.52 w/ 103.5 in memory location 01, !
;	146.52 w/107.2 in memory location 02, 146.52 w/110.9 in memory location 03). When the !
;	IC-706 is returned in HF mode with the RLC-3 (cmd 198) it still remains in split !
;	(offset) operation if a repeater pair was the last memory channel used (a problem if !
;	a HF freq (1.8-29.7) is to be used), another kludge changing CTCSS/PL/CG tones single !
;	freq - multi tone with RLC-3 cmd 198 operation (change to memory channel containg the needed tone, !
;	changing back to the frequency of proposed operation, setting the split on/off, setting !
;	offset needed +-600/+-1.0MHz+-5.0MHz etc. etc. requiring multi keypad entry to get the !
;	IC-706 set up for use. (event 209 and macro 690 fixes most of these problems but !
;	cmd 198 needs turned off and back on to reset the split off etc. / remember, the RLC-3 !
;	HF mode retains its info within the RLC's memory and doesn't have a clue what the IC-706's !
;	internal memories channel information contains and will cause conflicts between the two ways !
;	of getting the desired results of operation of the rig. A good understanding of both methods !
;	of communication with the ICOM rig will resolve most questions. !
;	It is very easy to use both methods with great results if the ground rules are followed. !
;	(the difference between information able to be stored in the radios internal memmories !
;	vs. what commands that can be sent to the ICOM rig via HEX/DEC commands and what commands !
;	the RLC-3 memory sends to the rig). !
;	!
;	!
;	!
;	Using the radios internal memory channels and the macros in this file, (instead of only !
;	using cmd 198) allows the Aux base to be able to connect to multiple ports using standard !
;	000, 001, 002 commands (using the ICOMS internal memory channels is not restricted to the !
;	RLC-3's 198 command for port connection). !
;	!
;	 ************************     PLEASE NOTE      *************************** !
;	 When renaming some of the 2 meter (or 440) frequencies - the RLC-3 010    !
;	 command will NOT allow more than 6 digits, therefore this file has errors !
;	 on every VHF(UHF) frequency that uses more than 6 digits                  !
;	 EXAMPLE:   " 146*625 ,  146*655   ,   146*685   ,  etc. "                 !
;	 ************************     PLEASE NOTE      *************************** !
;	!
;	!
;	73's de WB8YST  Jim Mangus !