* VERSION 2.16 UPDATE *

1) ADDED A WINDSPEED FACEPLATE TO ANALOG #8.  THIS ALLOWS THE RLC-ANG
THE ABILITY TO CONVERT AN EXTERNAL PULSE STREAM INTO A WIND SPEED.  THE
DEFAULT CALIBRATION IS SET TO HANDLE THE DAVIS INSTRUMENTS WIND SPEED SENSOR.
ANY PULSE WIND SENSOR CAN BE USED.  TO CALIBRATE THE WIND SPEED TO VOICE
CONVERSION:

WIND_SPEED_CALIBRATION =
	   60 / (WIND_SPEED_SENSOR <PULSES-PER-MINUTE-PER-MILE-PER-HOUR>)

FOR EXAMPLE:  THE DAVIS WINDSPEED SENSOR STATES ITS SENSOR OUTPUTS 26.6 PULSES
PER SECOND PER MILE PER HOUR.  WHEN DIVIDED BY 60 THE RESULT IS 2.256 SECONDS.
TO CALIBRATE THE SENSOR YOU WOULD ENTER: <COMMAND 15> 8 226 <ENTER OR UNKEY>.

SPECIAL NOTES:

A) YOU WILL NEED TO ADD A PULL-UP RESISTOR OF 10K TO YOUR WIND SPEED SENSOR
IF THE OUTPUT IS OPEN-COLLECTOR (STANDARD) INORDER TO CREATE A VOLTAGE PULSE
OUTPUT.  THE RLC-ANG REQUIRES THE WIND SPEED PULSES TO BE A VOLTAGE OUTPUT, NOT
JUST A PULSED INPUT.

B) YOU MUST REMOVE THE 10K DIVIDER (R41) INORDER TO HANDLE THE PULSE VOLTAGE
INPUT.

C) YOU MUST ASSIGN THE WINDSPEED FACEPLATE TO ANALOG 8: <COMMAND 13> 8 19.  THIS
ASSIGNS THE WIND SPEED CONVERSION TO ANALOG 8. FACEPLATE 19 IS THE WINDSPEED
FACEPLATE.

D) WHEN THE WIND IS CALM, THE VOICE WILL SPEAK "ZERO"


2) ADDED THE VOICE WORDS:
		 "EAST"  AS WORD 219
		 "NORTH" AS WORD 220
		 "SOUTH" AS WORD 221
		 "SPEED" AS WORD 222
		 "WEST"  AS WORD 223
		 "WIND"  AS WORD 224


3) CHANGED COMMAND <15> TO SUPPORT WINDSPEED READINGS

COMMAND <15> FORMAT IS:
	<COMMAND 15> # XXX	; ANALOG LINE CALIBRATION
	       - # IS THE ANALOG LINE
	       - XXX IS THE WIND SPEED CALIBRATION COUNTER

4) ADDED A WIND DIRECTION FACEPLATE THAT SPEAKS THE DIRECTION AS NORTH,SOUTH ECT.
	FACEPLATE 20 IS USED FOR THIS PURPOSE.

5) REMOVED THE TIME-OUT TIMER MESSAGE THAT WAS SPOKEN DURING A REPEATER
WHEN A TIME-OUT CONDITION OCCURRED.  WHEN A TRANSMITTER TIME-OUT OCCURS
NO MESSAGE WILL BE SPOKEN.

6) ADDED A UTILITY THAT IS RUN WHEN YOU SET-UP YOUR FACEPLATES THAT AUTO-
WRITES A MESSAGE IN THE ANALOG LINE SLOT YOU ARE SETTING UP.  THIS ALLOWS
THE USER TO SIMPLY SETS AN INPUT AS, FOR INSTANCE, TEMPERATURE AND THE PROGRAM
WILL WRITE A MESSAGE "THE TEMPERATURE IS XX" INTO ANALOG LINES MESSAGE SLOT.
THIS SIMPLFIES THE SET-UP OF THE RLC-ANG'S MESSAGE STRUCTURE.


THE MESSAGES ARE:

FACEPLATE:	MESSAGE;
   00		THE VOLTS IS XX
   01		THE VOLTS IS XX
   02		THE VOLTS IS XX
   03		THE VOLTS IS XX
   04		THE VOLTS IS XX
   05		THE VOLTS IS XX
   06		THE TEMPERATURE IS XX
   07		THE TEMPERATURE IS XX
   08		RADIO INPUT IS XX
   09		THE WIND IS FROM THE XXX
   10		RADIO INPUT IS XX
   11		THE INPUT IS <OPEN\CLOSED>
   12		THE INPUT IS <CLOSED\OPEN>
   13		THE INPUT IS <HIGH\LOW>
   14		THE INPUT IS <LOW\HIGH>
   15		THE INPUT IS <ON\OFF>
   16		THE INPUT IS <OFF\ON>
   17		THE BATTERY VOLTS IS XX
   18		THE CURRENT INPUT IS XX
   19		THE WIND SPEED IS XX
   20		THE WIND IS FROM THE <N\S\E\W...>

THIS SHOULD GREATLY SIMPLIFY THE SET-UP OF THE RLC-ANG'S ANALOG INPUTS.

   ********** THIS UPDATE REQUIRES RE-INITIALIZATION ****************
**** WHEN INITIALLY RUNNING V2.16, THEN RLC-ANG WITHH SELF INITIALIZE ****